Home. About Us. Products. News. Gallery. Support. Contact. Links. Pylon Line
High performance parts
						and engines.
Winning performance
Expert knowledge
For Pylon racing or
						Performance models

© 2012 Pylon Line


£8.25

Price:

IC 2000 (Burgandy Cap), 1 oz.

A rubber toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberghlass, rubber, carbon fiber and advanced materials. For model use IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife.


£4.95

Price:

Insta-Set Accelerator, 2 oz.

Spray bottle catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from the jointwhen parts are pressed together. Applying an additional bead of thick CA along the seam then curing it with INSTA-SET significantly enhances the joints strength. INSTA-SET activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastics and white foam.


Debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers.

£2.75

Price:

Un-Cure Debonder (Green Cap), 1 oz


Approx. 2 oz./Jar, 0.125" fibre length. Use as an additive with epoxy resins and adhesives to provide a very tough filler. Alternatively use as a filler in tight corners of moulding operations, such as wing fillets and propeller hubs.

£6.50

Price:

CST Chopped Graphite fibres, 2 oz. Jar  


With new cap that seals the bottle so it won't leak. Ideal for tool boxes and other places you don't want your CA glue to spill. A water thin viscosity CA that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam.

£4.65

Price:

Pocket Insta-Cure Thin, 3/4 oz.  


With new cap that seals the bottle so it won't leak. Ideal for tool boxes and other places you don't want your CA glue to spill. A higher viscosity CA for lose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds.

£4.65

Price:

Pocket Insta-Cure Gap Filler, 3/4 oz. Insta-Cure Super Thin CA Glue, 0.75 oz.


A water thin viscosity CA that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam.

£8.50

Price:

Insta-Cure Thin, 2 oz.


A higher viscosity CA for lose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds.

£8.50

Price:

Insta-Cure Gap filler, 2 oz.

£14.95

Price:

MGS LR285 resin 345g pack.

Pylon Line have been using this particular type of epoxy resin for the last 15 years, this resin has a German Federal aviation authority approval for the construction of full size aircraft, in that field it is used in particular for the construction of full size composite gliders.

The resin is definitely aimed at the construction of high performance components, where it is amongst the top few products available however it could also be used for glass cloth covering. Typical uses in models include fuselage and wing construction, laminating composite propellers, laminating U/C's and repair of existing structures.

Supplied with highly detailed 8 page instructions, giving all required data plus more!